LED Fold Down All Around Light for Pontoon Boat - 24" LED Fold Down 360° All Around Pontoon Lights are approved for USCG 2 NM (Colreg 2 mile). Mounts on 1-1/4" square tubing. Constructed of injection molded nylon and aluminum. Installs with three #10 FH fasteners (not included). 12VDC. Low amp draw. All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. |
LED Fold Down All Around Light for Pontoon Boat - 9" LED Fold Down 360° All Around Pontoon Lights are approved for USCG 2 NM (Colreg 2 mile). Mounts on 1-1/4" square tubing. Constructed of injection molded nylon and aluminum. Installs with three #10 FH fasteners (not included). 12VDC. Low amp draw. All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
LED Masthead Light - 2 NM - 225° LED 225° Masthead Lights are fixed mounted and approved for USCG 2 NM (Colreg 2 mile). Constructed of UV stabilized injection molded polycarbonate. Installs with two #12 RH fasteners (not included). 12VDC. Low amp draw. All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
LED Pop Out Combination Bow Light The LED Pop-Out Combination Bow Light is approved for USCG 2 NM (Colreg 2 mile). A simple twist of the cap allows the light to pop up, ready to use when it’s switched on. Push the cap down, twist to lock, and light disappears into the deck. Constructed of corrosion resistant investment cast stainless steel cap and bezel. Installs with three #10 fasteners (included). IP67 waterproof rating. All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
LED Removable Telescopic All Around Light - 26" - 48" LED Removable Telescopic 360° All Around Lights are approved for USCG 2NM (Colreg 2 mile). Constructed of injection molded nylon and aluminum. 12VDC. Low amp draw. Installs with three #8 FH fasteners (not included). All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Magneto Safety Kill Switch Marine emergency cut-off Kill Switch attaches to your life vest while operating a boat or personal watercraft. Designed to instantly cut battery power when detached. The magneto (red cap) version functions in applications where the circuit is normally open (not complete) with lanyard clip in place on switch. When lanyard is pulled and clip is removed from switch, circuit is closed (complete), allowing grounding to a suitable ground such as a grounding block, the battery, or a suitable area on the engine itself. The kill switch includes a coiled lanyard that is approximately 15" when coiled and 48" when stretched, which should be replaced if worn, cut, or frayed. Mounting hole is 5/8" in diameter. Maximum panel thickness: 5/8". Maximum 5A draw. WARNING: Switch should be tested for proper function before each use. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Max Blast Single Mini Compact Horn Max Blast Single Mini Compact Horn is constructed of injection molded housing under the stamped 304 stainless steel cover, which protects the internal components from corrosion. After a 600 hour salt spray test, this electric horn was completely rust-free! Mounting bracket can be used as a wiring template. When installed, horns should point slightly downward to permit water drainage. At 108 decibels and a frequency (Hz) of 440±20A, this horn meets US Coast Guard's COLREGS and ABYC standard A-23 for use on vessels under 12m (39'). 12VDC. Five-year rust-free warranty. 12VDC. NMMA Type Accepted #2577060. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Max Blast Twin Mini Compact Horn MaxBlast Twin Mini Compact Horn is constructed of injection molded housing under the stamped 304 stainless steel cover, which protects the the internal components from corrosion. After a 600 hour salt spray test, this electric horn was completely rust-free! Mounting bracket can be used as a wiring template. When installed, horns should point slightly downward to permit water drainage. At 111 decibels and a frequency (Hz) of 490±20A, this horn meets US Coast Guard's COLREGS and ABYC standard A-23 for use on vessels under 12m (39'). 12VDC. Five-year rust-free warranty. 12VDC. NMMA Type Accepted #2577062. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
MaxBlast Air Horn - Dual Trumpet MaxBlast Dual Trumpet Air Horn is constructed of durable chrome plated brass. When installed, the trumpet should point slightly downward to permit water drainage. Display pack includes horn, compressor, air tubing, and mounting hardware. At 121 decibels and a frequency (Hz) of 375±15A/315±15A, this horn meets the US Coast Guard's COLREGS, US Inland Navigation Rules, Annex III Regulations, and ABYC standard A-23 for boats up to 20 meters (66’). 12VDC. Maximum: 20A. NMMA Type Accepted #2577055. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
MaxBlast Air Horn - Mini Dual Trumpet MaxBlast Mini Dual Trumpet Air Horn is constructed of durable chrome plated brass. When installed, the trumpet should point slightly downward to permit water drainage. Display pack includes horn, compressor, air tubing, and mounting hardware. At 125 decibels and a frequency (Hz) of 630±15A/525±15A, this horn meets the US Coast Guard's COLREGS, US Inland Navigation Rules, Annex III Regulations, and ABYC standard A-23 for boats up to 20 meters (66’). 12VDC. Maximum: 20A. NMMA Type Accepted #2577058. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
MaxBlast Air Horn Compressor - 12V The MaxBlast Air Horn Compressor works with all Sea-Dog® MaxBlast air horns. For use in standard installations where head room is not an issue. Does not include air tubing or mounting hardware. Maximum: 20A. 12 or 24VDC. CE compliant. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
MaxBlast Air Horn Compressor - 24V The MaxBlast Air Horn Compressor works with all Sea-Dog® MaxBlast air horns. For use in standard installations where head room is not an issue. Does not include air tubing or mounting hardware. Maximum: 20A. 12 or 24VDC. CE compliant. |
MaxBlast Stainless Steel Trumpet 12V Horn - Dual MaxBlast Dual Trumpet Air Horn is constructed of durable stainless steel. When installed, the trumpet should point slightly downward to permit water drainage. Specifications:
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
MaxBlast Stainless Steel Trumpet 12V Horn - Single MaxBlast Single Trumpet Air Horn is constructed of durable stainless steel. When installed, the trumpet should point slightly downward to permit water drainage. Specifications:
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Motor Well Boot - 3" Split Black accordion style seal organizes and protects engine control cables, wires or fuel lines. UV stabilized molded rubber. Boots and rings are cut for trouble free installation without removal of cables. Includes tie wrap. |
Motor Well Boot - 4" Split Black accordion style seal organizes and protects engine control cables, wires or fuel lines. UV stabilized molded rubber. Boots and rings are cut for trouble free installation without removal of cables. Includes tie wrap. 5 1/2" diameter |
Motor Well Boot - 5-1/2" Black accordion style seal organizes and protects engine control cables, wires or fuel lines. UV stabilized molded rubber. Includes mounting ring. |
Nylon Adjustable Flagpole Clamps - 1/2" - Pair The flag is attached to the flagpole using sliding, black nylon pennant mounts. Both pennant mounts are adjustable in either direction on the flagpole allowing flexibility in mounting various sizes of flags. |
Nylon Boat Hook/Paddle Clip UV stabilized injection molded nylon construction. One-piece boat hook/paddle clip allows for the simple one handed storage of your boat hook or paddle. Anti-snag ramps prevent line from getting stuck under the clip when not in use. Features leash attachment points for securing a paddle leash. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Nylon Deck Fill Key Deck Fill Key is constructed of injection molded black nylon. For use with all Fill Caps featuring 1-3/16" holes on center. |
Nylon Fendermate™ Fendermate™ is the latest in fender brackets. Clamps securely on both 7/8" and 1" round tubing and 3/16" and 1/4" life line wire. Unique double locking action locks the clamp on the rail or wire while still allowing full adjustment of the height of the fender. When the proper height is reached, the final locking action clamps the rope quickly and securely. Constructed of marine grade reinforced injection molded nylon. |
Nylon Flagpole Pennant Mounts & Stainless Clips - Pair The Sea-Dog® Adjustable Rail Mount Flagpole is constructed of highly polished, heavy wall stainless steel tubing with an injection molded nylon rail mount bracket. The flag is attached to the flagpole using nylon adjustable flagpole clips in conjunction with stainless steel, spring wire, quick release clips which allows mounting flexibility for a variety of flag or pennant sizes. For use on either 7/8" or 1" tubing. Maximum speed 10 MPH. |
Nylon Switch Panel - Water Resistant - 5 Toggles with Power Socket The Water Resistant Toggle Switch Panel features five 15A 12VDC toggle switches, a 12VDC power socket, inline fuse holders, and a decal sheet. Constructed of injection molded ABS. Installs with four #6 RH fasteners (not included). |
Nylon Tube Connector - Black - 7/8" Tube Connectors are used for connecting the ends of stainless steel or aluminum tubing by sliding inside the tube. Fits 7/8” tubing. Constructed of injection molded nylon. *Stainless tube wall thickness 0.049”. |
Nylon Windshield Brace Foot Kit with Tube Windshield Brace Kit includes two windshield brace feet and a 14-1/4" length of formed aluminum tube to be cut to size per individual application. Injection molded nylon brace feet inserts must be crimped in place. Installs with #10 PH screws (not included). Direct replacement for Taylor Made TMS-041. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
Oblong Captive Garboard Drain & Plug - 316 Stainless Steel This Oblong Captive Garboard Drain & Plug sits lower in the stern for more water removal. Captive plug prevents plug from being lost. Constructed of corrosion resistant investment cast 316 stainless steel. Installs with two #8 FH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. |
OLED Voltmeter - Round The OLED (Organic LED) Voltmeter is designed to withstand constant vibration and the rigors of a marine environment. Monitors voltage on a bright, waterproof, daylight readable OLED screen. High contrast and resolution make this screen visible from a wide viewing angle, even with polarized sunglasses. Reverse polarity protected. Constructed of injection molded nylon with terminal spade contacts. Installation is as easy as drilling a 1-1/8" hole, inserting the socket body, tightening the locking nut, and connecting the wires. Also fits Sea-Dog® Power Socket Shell (426100) and Mounting Bracket (426105). Input 8-60VDC. IP66 rating. |
Plugmate™ Garboard Wrench The Garboard wrench features multiple deck keys. Constructed of durable injection molded polypropylene it fits standard garboard plugs as well as "T" style plugs. The 520045-1 includes one replacement plug stored in handle. |
Poly Rail Mount Motor Bracket - Black Injection Molded Polypropylene These Rail Mount Motor Brackets are designed to hold small, 2-cycle outboards up to 8 HP upright on the stern rail. Will fit both 7/8" and 1" rails, as well as rails using 90° tee fittings. Most other polypropylene and wood motor brackets only fit 1" welded rails. The two-piece unit features extra holes, enabling the use of a recommended chain to secure the motor. Can also be used as a mounting platform for barbecues, down rigger brackets, fish cleaning tables, etc. Constructed of UV stabilized polypropylene. Includes all necessary fasteners. |
Poly Rail Mount Motor Bracket - White Injection Molded Polypropylene These Rail Mount Motor Brackets are designed to hold small, 2-cycle outboards up to 8 HP upright on the stern rail. Will fit both 7/8" and 1" rails, as well as rails using 90° tee fittings. Most other polypropylene and wood motor brackets only fit 1" welded rails. The two-piece unit features extra holes, enabling the use of a recommended chain to secure the motor. Can also be used as a mounting platform for barbecues, down rigger brackets, fish cleaning tables, etc. Constructed of UV stabilized polypropylene. Includes all necessary fasteners. |
Pontoon Boat Mini Compact Horn with Bracket Pontoon Boat Mini Compact Horn with Bracket is constructed of powder coated steel. Includes 304 stainless steel bracket for easy mounting. Recommended for fresh water applications. At 111 decibels and a frequency (Hz) of 370±20A, this horn meets US Coast Guard's COLREGS and ABYC standard A-23 for use on vessels under 12m (39'). 12VDC. NMMA Type Accepted #2601746. |
Rail Base Fitting Rectangular Base 30° 316 Stainless Steel - 1-7/8" x 32-3/16" - 1" OD These Rectangular Rail Base Fittings include set screws where appropriate. Set screws can be purchased separately (299999-1). Requires 1/8" Allen wrench to install. Constructed of corrosion resistant investment cast 316 stainless steel. Installs with four FH fasteners (not included). *Stainless tubing with a wall thickness of 0.049”. Features:
|
|
|
|
|
Copyright © 2009-2024 A part of the Intelastores, Inc. Store Network Site Designed and Maintained by Inline Internet Systems, Inc. |