J-BASE for Windex 15
This optional mount for Windex 15 provides more versatility and reduces overall weight aloft by 15 grams when substituted for standard Windex 15 mounting base. The J-Base comes with two #10 (5 mm) selftapping screws. Drill a pilot hole in mast, apply silicone sealant or Locktite® and screw into mast. Installation of J-Base can also be accomplished by tapping the mast for 3/16" (5 mm) machine screws or by using epoxy putty to affix base to the mast |
Leaf Wetness Sensor, Vantage Pro® and Vantage Pro2
Use to monitor the level of surface moisture on foliage, with range from 0 (completely dry) to 15 (saturated). Add up to 2 sensors to a single Wireless Leaf & Soil Moisture/Temperature Station. Includes 40' (12M) cable. Compatible with both original Vantage Pro and Vantage Pro2. The Leaf Wetness Sensor must be connected via a Leaf & Soil Moisture/Temperature Station (#6345). |
lil' Fella Trolling Plate
Little brother to the Happy Troller®
|
Wireless Long-Range Repeater with Solar Power
For those who wish to send weather data much farther than 1,000' (300M), the Wireless Long-Range Repeater can extend the range up to two miles (3.2 km). Please note: Use of this product requires a pair of external antennas, sold separately.The Long-Range Repeater has a transmitting and a receiving cable, each with an end which will connect to an external antenna. Choose either our large omni directional antenna (#7656), range 1,560' (476 m) in all directions, or our Yagi directional antenna (#7660), range 5,000' (1.5 km) in one direction. You'll need two antennas for each Long-Range Repeater. The charging system is capable of performing continuously even under low light conditions. Includes solar panel, regulator circuit, and rechargeable battery. Compatible with Vantage Pro2 and Vantage Vue only. Not compatible with original Vantage Pro. |
Lube II
Lube II allows sticky, hard to move steering rods to be properly and easily lubricated for smooth, easy steering action.The system includes a stainless steel lubricating nut with an oil seal and a grease (zerk) fitting. This lubricator's unique design keeps moisture and contaminants out while enabling you to pour or pump several types of lubricant in. Works for both mechanical and hydraulic systems. Fits all major US and foreign motors (7/8" x 14 pitch threads). Easy installation. Marine grade stainless steel nut for salt and fresh water use |
Mark 15 Sextant
#026 This model has many great features including seven large sunshades, a 3 mm x 27 mm star scope, and easy-to-read micrometer drum vernier scale that reads to 2/10 of a minute. The Mark 15 has a 7" (18 cm) frame radius graduated from 120° to -5° and comes with a traditional half-silvered mirror. Comes with instruction booklet. |
Mark 3 Marine Sextant
Sometimes referred to as a "lifeboat" sextant, the Mark 3 is an inexpensive training sextant. Yet this model has taken sailors around the world, too! It is full-sized and has sunshades, but no optical magnification to help you find dim celestial bodies. Comes with instruction booklet. |
Max-Lube
Max-Lube excels in performance under pressure - anywhere oil is required. This proprietary synthetic film has many advantages over other synthetic and premium oils:
The net result is smoother, quieter, cooler, and longer operation. Recommended for steering cables (all boat motors, fresh or salt water), sporting equipment, all gears regardless of type or size, and all metals. Comes in a 3 fl.oz (90 ml) container. |
Motor Caddy
Motor Caddy is sized to be quickly attached to most outboards from 2-15 horsepower. This improved design features a longer strap to fit 4-stroke motors and an added security strap for today's streamlined engine cases. Made of UV resistant materials that will endure the marine environment for those who prefer a semi-permanent installation. Glass filled nylon buckles insure that Motor Caddy is easy to install and remove. Makes lifting and moving cumbersome motors safer and simpler. |
Mounting Pole Kit
Poles and hardware for mounting Vantage family stations or sensors. Kit includes two poles and mounting hardware. Poles can be used seperately or together to make a single, larger pole. Specifications
|
Mounting Tripod
Optional tripod makes installation even easier. Brackets at the base of each leg tilt to mount on your roof or uneven terrain. Made of galvanized steel. Includes two .92 m -long poles, which may be used separately or together to make a single 1.77m- long pole. |
Omni Antenna for Long-Range Repeater
Use with Long-Range Repeater to extend range up to 1,560' in all directions. Each repeater requires two antennas. You can combine omni and Yagi antennas to collect data from all directions and transmit in a single direction, or vice versa.Includes mounting hardware. NOTE: FCC regulations require that U.S. customers select either the Omni Antenna (#7656) or the Yagi Antenna (#7660); customers outside the U.S. must purchase third-party antennas in compliance with local regulations |
Prop Sox
Prop Sox protect your expensive propellers from road kickback when towing and promote safety by increasing your propellers' visibility. Prop Sox are made of bright plastic and simply slip over each propeller blade. The sox are held in place with a rubber cinch strap. Set of three socks, cinch straps and 3 reflector hot-dots included. For use when your boat is out of the water only. |
Radiation Shield
The most effective passive shelter available. Protects your Temperature or Temperature/Humidity Sensor from solar radiation and other sources of radiated and reflected heat. Multi-plate construction for maximum airflow. Asssembly required. May be used with Sensor Mounting Arm or mounted on metal pipe or wood surface. Use for Wizard II and Monitor II stations. |
Rain Collector Heater
This product will work with our Vantage Pro and Vantage Pro2 wireless weather stations, however, the heater must be plugged into an electrical outlet. This product cannot be used with our any of our Solar Power Kits or the Vantage Vue station. Use in cold climates to measure freezing rain or the moisture content of snowfall. Includes:
|
Rain Collector Cone & Heater f/AeroCone - *Not For Use With Classic Rain Cone
Rain collector cone and heater replacement kit Vantage Pro2 rain collectors with AeroCone. Heats ice and snow to keep your rain collector from freezing. All Vantage Pro2 stations come with the AeroCone. Unfortunately, the heater will not fit inside the AeroCone. This kit includes the heater and the larger old style cone to replace the AeroCone for those freezing winters that bring snow and ice. Keep snow from filling your Vantage Pro2 rain collector with this heater. Great for use in cold climates to measure freezing rain or the moisture content of snowfall. The heater warms the inside of the cone during cold weather. A thermostat switch turns the power off when temperatures rise and back on when they fall. Note: The heater must be plugged into an electrical outlet. Heater is not compatible with AeroCone; it is only compatible with the old style, larger rain cones. Specifications:
Includes:
Requires:
|
Rocker Stopper Boat Stabilizer Rocker Stoppers help dampen the rocking motion of boats at anchor. Simply tie Rocker Stoppers approximately 44 cm (18″) apart, making a string of them, with a 5-10 pound weight attached at the bottom of the string. Hang one string off each side of the boat. Just four units per side are what it takes on most boats to 36′. Be sure you hang them where they will always be underwater. Many people use mushroom anchors with their Rocker Stoppers because this type of weight nests well inside the last Rocker Stopper in your string. Use 10 mm (3/8″) braided nylon or 3-stranded nylon line. Use without a weight (or with reduced weight) for drift fishing. Rocker Stoppers will slow down drift substantially. They are also great to use at the end of a dock to stabilize the tip from rocking. Rocker Stoppers nest together and each one is 33 cm (14″) in diameter. It’s lightweight and molded of high impact, virtually indestructible styrene. Can be deployed or retrieved in seconds. Unaffected by salt water and cannot affect the sides of your boat. Units are made to “nest” within each other, so storage is a breeze. Number of Rocker Stopper Units Needed on Each Side of the Boat (Sail or Power):
|
Round Sail Track Stops
Round 0.50" dia. x 0.875" (13 x 22mm) When it's time to lower your sail you can rely on Davis' Round Sail Track Stop to hold your sail and its slides in place on the mast and boom. Large knurled wheels are released with ease. Made of heavy-duty, black anodized aluminum and marine garde nickel plated brass. |
Rudder Position Indicator
Awareness of the rudder angle is an important safety factor. This is especially true while moving in and out of your berth, drawing alongside another boat, picking up a skier, mooring, or any other "close call" situation. Davis' Rudder Position Indicator gives instant visual reference of rudder angle. The pointer swings a full thirty degrees with each revolution of the wheel. Mounts directly to your hub (approximately 2" (5 cm) in diameter) with a self-adhesive pad . Rugged, hermetically sealed, weatherproof, and sunproof housing ensures long life. No cables, adjustments, or electricity required; gravity power makes it simple and service-free. Suitable for boats with mechanical and single station hydraulic steering systems. |
Secure Removable Chafe Guards - Black (Pair)
Chafe protection is critical at the dock, at anchor, or on a mooring. The Chafe Guard is a good solution to prevent chafing over a cleat, cap rail, where two lines cross or at the anchor roller. Dock lines can be expensive; extending their life with good chafe protection is not. Removable Chafe Guards fit 3/8" to 7/8" line (10 mm to 23 mm). Great for anchor lines or mooring pennants, where chafing through a line could cost you the boat. Velcro_ brand hook fasteners on the inside of the guard grip the line securely; no need for additional strings or ties. Easily reposition when dock lines stretch and chafe protection needs to moved. Made of nylon. Sold by the pair. Each chafe guard is 16" long (40 cm). |
Secure Removable Chafe Guard - White (Pair)
Chafe protection is critical at the dock, at anchor, or on a mooring. The Chafe Guard is a good solution to prevent chafing over a cleat, cap rail, where two lines cross or at the anchor roller. Dock lines can be expensive; extending their life with good chafe protection is not. Removable Chafe Guards fit 3/8" to 7/8" line (10 mm to 23 mm). Great for anchor lines or mooring pennants, where chafing through a line could cost you the boat. Velcro® brand hook fasteners on the inside of the guard grip the line securely; no need for additional strings or ties. Easily reposition when dock lines stretch and chafe protection needs to moved. Made of nylon. Sold by the pair. Each chafe guard is 16" long (40 cm). |
Sensor Mounting Shelf
For mounting solar radiation sensor and/or UV sensor on Vantage Pro and Vantage Pro2 integrated sensor suite. Rigid shelf with anodized aluminum posts and stainless steel hardware attaches easily next to the rain collector on the outside of the integrated sensor suite. Compatible with both original Vantage Pro and Vantage Pro2. |
AnchorSnubber
20" Long Eases the tension on the anchor chain, rode or snubber line. Eliminates chain noise and shock loads to chain, anchor roller, windlass, cleats. |
DockShockle
Designed for smaller, lighter boats up to 40'. DockShockle is 16" Long. Includes two special mini-LineGrabbers for quick and easy attachment. |
FenderFriend
A reliable way to keep your boat fenders in place. Nylon buckle for swift, secure attachment without complicated knots. FenderFriend stretches to avoid shock to your rails, stanchions, life lines or cleats. |
LineGrabber
Add a strong, instant attachment point with a simple Prusik knot to any line up to 1". LineGrabbers are 9" long with spliced and sewn loops at each end. Made of UV resistant composite fiber line. |
Shockles LineSnubber
20" Long Eliminates shock loads on dock lines, towing lines, tie-downs and preventers. Progressive tension design with internal stretch limiter. |
Shockles LineSnubber
20" Long Eliminates shock loads on dock lines, towing lines, tie-downs and preventers. Progressive tension design with internal stretch limiter. |
MiniShockle
12" Long This is a bungee cord on steroids! MiniShockles hold up to 300lbs to protect your valuable gear. Ten times stronger than a standard bungee cord. |
MiniShockle
18" Long This is a bungee cord on steroids! MiniShockles hold up to 300lbs to protect your valuable gear. Ten times stronger than a standard bungee cord. |
MiniShockle
24" Long This is a bungee cord on steroids! MiniShockles hold up to 300lbs to protect your valuable gear. Ten times stronger than a standard bungee cord. |
Snap Tool Multi-Key
A deck plate with attitude!
Perfect for:
|
|
|
|
|
Copyright © 2009-2024 A part of the Intelastores, Inc. Store Network Site Designed and Maintained by Inline Internet Systems, Inc. |